View unanswered posts | View active topics It is currently December 13th, 2018, 6:33 am



Reply to topic  [ 147 posts ]  Go to page Previous  1 ... 6, 7, 8, 9, 10
 Ed's loader 
Author Message
UC4x4 Member
User avatar

Joined: June 11th, 2007, 11:43 am
Posts: 10559
Location: Tracy, CA
Post Re: Ed's loader
bummer on the leak. Hopefully it will be leak free on the next attempt.

_________________
Early "CLASSIC" Bronco ower. {o===o}
The NEW best truck weight guesser guy!


November 28th, 2018, 7:31 am
Profile WWW
User avatar

Joined: April 13th, 2014, 7:15 pm
Posts: 1825
Location: Fresno, CA
Post Re: Ed's loader
Yeah, I dunno. Maybe the seal was damaged going in, it wasn’t an easy install. We didn’t have a socket the right size to contact the metal part of the seal fully. I will next time. Or maybe the fit isn’t right between yoke and seal?? It’s a Terex seal with the part number the book says to use. The sealing surface on the yoke looked good. Maybe it’s leaking past the splines? It doesn’t have a nut, it has two threaded holes in the end of the shaft. There’s a plate with two holes that retains it. The plate looked worn on the seal side, we turned it around and used silicone. I’ll know more next time.

_________________
1964 International 1ton, D70F ARB, RA15 Detroit Locker, dual transmissions, 375:1 crawl ratio, 41" Iroks, flat bed.


November 28th, 2018, 8:19 am
Profile
User avatar

Joined: April 13th, 2014, 7:15 pm
Posts: 1825
Location: Fresno, CA
Post Re: Ed's loader
The transfer output is like this, it doesn’t have a big nut on it. It’s leaking past the seal though, not the splines. My mechanic friend thinks the spring may have popped off the back of the seal, I didn’t think of that possibility. He wants to take off the retainer the seal is installed into, and look at it from the back side.


Attachments:
AE044330-3A8F-4B48-9E38-4DA9691EC405.jpeg
AE044330-3A8F-4B48-9E38-4DA9691EC405.jpeg [ 2.25 MiB | Viewed 70 times ]

_________________
1964 International 1ton, D70F ARB, RA15 Detroit Locker, dual transmissions, 375:1 crawl ratio, 41" Iroks, flat bed.
November 29th, 2018, 10:01 pm
Profile
User avatar

Joined: April 13th, 2014, 7:15 pm
Posts: 1825
Location: Fresno, CA
Post Re: Ed's loader
I still can’t figure out where the block heater goes, I think what I got is for a later engine. The people selling these things are no help. Well almost no help, their product information says it replaces the water jacket plate on the side of the engine. They have two options, with and without water cooled compressor. Mine is water cooled. So I think if I follow the hose back from the compressor, it will go to where this thing installs at. It’s just a pipe fitting though. I can’t find anything with two bolts like this.

So I guess the question is, what/where is the water jacket plate? I don’t have engine manuals for this yet, the machine manuals only show a limited amount of engine stuff. It might show what I need to know, I will look.


Attachments:
3C3CC7F4-51E1-4CBC-B4D9-8DF316C16179.jpeg
3C3CC7F4-51E1-4CBC-B4D9-8DF316C16179.jpeg [ 361.05 KiB | Viewed 64 times ]

_________________
1964 International 1ton, D70F ARB, RA15 Detroit Locker, dual transmissions, 375:1 crawl ratio, 41" Iroks, flat bed.
November 30th, 2018, 9:09 pm
Profile
User avatar

Joined: April 13th, 2014, 7:15 pm
Posts: 1825
Location: Fresno, CA
Post Re: Ed's loader
This is what I found when I got there, plus there were three new trees down parallel to the loader just downhill. Three new ones across the main road, and two new ones across my lower road. And, I came in from the top in the snow. Neighbors came in from the bottom, and had to cut through twenty trees to do it. They were in a two wheel drive, going to drain the water in their cabin. I pulled them to their driveway, above ours, and got them turned around. It is raining trees, doh! I dropped another 9-10 in the area I want to move it to. Loader is ready to move, and another 3 day break in the weather is coming.

Edit: In the 3rd image you can see the air cleaner bonnet was damaged by the tree, already got a replacement.


Attachments:
FC914877-4A06-4446-B24A-190E0FEB8CD2.jpeg
FC914877-4A06-4446-B24A-190E0FEB8CD2.jpeg [ 3.44 MiB | Viewed 45 times ]
315AC834-5E58-4927-8BA6-E598A3BB2C9E.jpeg
315AC834-5E58-4927-8BA6-E598A3BB2C9E.jpeg [ 3.61 MiB | Viewed 45 times ]
857F973B-F00C-4381-B564-9060460047AF.jpeg
857F973B-F00C-4381-B564-9060460047AF.jpeg [ 3.27 MiB | Viewed 45 times ]
D7DF12BF-4637-4F80-9D97-71698E9A9CE4.jpeg
D7DF12BF-4637-4F80-9D97-71698E9A9CE4.jpeg [ 3.44 MiB | Viewed 45 times ]
EBBFF9F2-EC0D-4A81-AE01-6ABA4F17FEC7.jpeg
EBBFF9F2-EC0D-4A81-AE01-6ABA4F17FEC7.jpeg [ 3.03 MiB | Viewed 45 times ]

_________________
1964 International 1ton, D70F ARB, RA15 Detroit Locker, dual transmissions, 375:1 crawl ratio, 41" Iroks, flat bed.


Last edited by Big Ed on December 6th, 2018, 10:38 pm, edited 1 time in total.

December 5th, 2018, 7:54 am
Profile
UC4x4 Member
User avatar

Joined: September 25th, 2006, 8:46 pm
Posts: 12635
Location: San Jose
Post Re: Ed's loader
How rude of that tree to take out your tire stand!

_________________
"He who exercises government by means of his virtue
may be compared to the north polar star, which keeps its place and all
the stars turn towards it."

- Confucius


December 6th, 2018, 9:06 pm
Profile WWW
User avatar

Joined: April 13th, 2014, 7:15 pm
Posts: 1825
Location: Fresno, CA
Post Re: Ed's loader
Dan90FSB wrote:
How rude of that tree to take out your tire stand!


Wut?

_________________
1964 International 1ton, D70F ARB, RA15 Detroit Locker, dual transmissions, 375:1 crawl ratio, 41" Iroks, flat bed.


December 6th, 2018, 10:33 pm
Profile
User avatar

Joined: April 13th, 2014, 7:15 pm
Posts: 1825
Location: Fresno, CA
Post Re: Ed's loader
Both front wheels are back on, the tripod actually did pretty good. Just had to walk it in a few times. In the closeup pic you can see a guide pin starting onto a hole, they made it a whole lot easier.


Attachments:
89E17CCB-7F9D-455B-9A21-493525521385.jpeg
89E17CCB-7F9D-455B-9A21-493525521385.jpeg [ 4.65 MiB | Viewed 32 times ]
B9CBAA53-491B-43B2-B9B7-AE07B736537A.jpeg
B9CBAA53-491B-43B2-B9B7-AE07B736537A.jpeg [ 3.49 MiB | Viewed 32 times ]
440AAF17-1366-48A5-B433-AD036A26C9F9.jpeg
440AAF17-1366-48A5-B433-AD036A26C9F9.jpeg [ 3.94 MiB | Viewed 32 times ]

_________________
1964 International 1ton, D70F ARB, RA15 Detroit Locker, dual transmissions, 375:1 crawl ratio, 41" Iroks, flat bed.
December 6th, 2018, 11:29 pm
Profile
User avatar

Joined: April 13th, 2014, 7:15 pm
Posts: 1825
Location: Fresno, CA
Post Re: Ed's loader
California Monkey wrote:
bummer on the leak. Hopefully it will be leak free on the next attempt.


Leak free now, the seal was torn. Oops! Installed new seal.

_________________
1964 International 1ton, D70F ARB, RA15 Detroit Locker, dual transmissions, 375:1 crawl ratio, 41" Iroks, flat bed.


December 7th, 2018, 12:36 pm
Profile
User avatar

Joined: April 13th, 2014, 7:15 pm
Posts: 1825
Location: Fresno, CA
Post Re: Ed's loader
I drilled the hex plate mounting bolts for safety wires, I don’t want it lost again.


Attachments:
F24BAC30-3327-4768-9AC5-61CB345B12BF.jpeg
F24BAC30-3327-4768-9AC5-61CB345B12BF.jpeg [ 3.1 MiB | Viewed 29 times ]
44923351-F683-446E-B5A2-4CB74EDEE5B5.jpeg
44923351-F683-446E-B5A2-4CB74EDEE5B5.jpeg [ 4.16 MiB | Viewed 29 times ]

_________________
1964 International 1ton, D70F ARB, RA15 Detroit Locker, dual transmissions, 375:1 crawl ratio, 41" Iroks, flat bed.
December 7th, 2018, 12:41 pm
Profile
User avatar

Joined: April 13th, 2014, 7:15 pm
Posts: 1825
Location: Fresno, CA
Post Re: Ed's loader
The tree broke the door handle off, already ordered a new one.


Attachments:
149D3405-D009-42C8-BB5F-8409BB5B8EC1.jpeg
149D3405-D009-42C8-BB5F-8409BB5B8EC1.jpeg [ 2.2 MiB | Viewed 19 times ]

_________________
1964 International 1ton, D70F ARB, RA15 Detroit Locker, dual transmissions, 375:1 crawl ratio, 41" Iroks, flat bed.
December 9th, 2018, 10:51 am
Profile
User avatar

Joined: April 13th, 2014, 7:15 pm
Posts: 1825
Location: Fresno, CA
Post Re: Ed's loader
You can see a branch between the tire and “grabber”, it was to keep the grabber from shifting over and coming out of the rim on the back side. I made the grabber too wide, doh! On the second wheel we left out one of the two bolts holding the two grabber halves together, so it closed in on the wheel. Worked well.


Attachments:
E249BE5A-4251-4B6C-882D-B6C6DB65D95C.jpeg
E249BE5A-4251-4B6C-882D-B6C6DB65D95C.jpeg [ 3.6 MiB | Viewed 19 times ]

_________________
1964 International 1ton, D70F ARB, RA15 Detroit Locker, dual transmissions, 375:1 crawl ratio, 41" Iroks, flat bed.
December 9th, 2018, 11:03 am
Profile
Display posts from previous:  Sort by  
Reply to topic   [ 147 posts ]  Go to page Previous  1 ... 6, 7, 8, 9, 10

Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by STSoftware.